Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

RF · Microwave · PCB · Signal integrity

Engineering calculators that show their work.

Transmission lines, matching networks, filters, antennas and link budgets. Each tool names the published model it implements, states where that model stops being accurate, and solves for any input, so you can ask for 50 Ω and get the trace width.

Calculators
22
Reference checks
1036
Inputs uploaded
0
Microstrip · RO4350B 20 mil · 10 GHz34 reference checks
Microstrip cross-section: trace of width W and thickness T on a substrate of height H over a ground planeWHTεr
Z₀(f)
49.37Ω
εeff(f)
2.868
Delay
143.5ps/in
Loss
0.209dB/in

In developmentCables & connectors · Signal integrity · EMC / EMI · Waveguides & cavities · IC & packaging

How the numbers are checked

A calculator you can't verify is a liability. These are the rules every tool here follows.

Read the full method →
Published models
Each calculator implements equations from the literature: Hammerstad and Jensen, Kirschning and Jansen, Cohn, Wheeler, Pozar, Balanis and others. The equations and full citations are on every page.
Independent reference values
1036 expected values, taken from textbook examples, exact analytic limits and independent software (scikit-rf, SciPy, a 2-D field solver), are re-checked on every change. A result that drifts out of tolerance cannot be deployed.
Stated limits
Closed-form models are only accurate over certain ranges. When your inputs leave a model's validated range, the calculator says so next to the result instead of silently extrapolating.
Computed in your browser
Your design values never leave your machine. Share links carry the inputs in the URL, so only the people you send them to see them.